/ boiler & process design software
Built by a 25+ years veteran engineering consultant, for the engineers who design and run the world's thermal and biomass power systems.
WHAT'S INSIDE
Every calculator is free, runs in your browser, and shows how much checking stands behind it.
Every module here is a working calculator, not a mockup. Each carries a status badge showing how much checking stands behind it: Validated against a reference design calculation or published example, Reference-based on published methods, or Preliminary while awaiting a reference check. See what each badge means.
Size backward-curved centrifugal fans, check single-curve blade geometry against target diameters, and generate the full static-pressure-versus-flow performance curve.
Open calculatorReal atmospheric pressure from site elevation, full psychrometric state from wet-bulb or RH, and mixed-gas viscosity, conductivity and Cp for fan and drying work.
Open calculatorSaturated and superheated/subcooled water & steam properties from the official international formulation — also the shared data source behind future Boiler, Economizer and Evaporator modules.
Open calculatorDense/near-critical supercritical water and ultra-high-temperature steam above 800°C — including viscosity and thermal conductivity — for supercritical boiler design and furnace/gas-turbine work beyond the standard range.
Open calculatorProximate, ultimate and ash-oxide analysis for common Thai biomass fuels, plus custom fuel entry with automatic As-Received/Dry-basis conversion — shared data for the Combustion and Boiler modules.
Open calculatorBlend two fuels by as-received weight percentage into a combined Proximate, Ultimate and ash-mass-weighted Ash Oxide analysis — for co-firing and blended-feedstock boiler design.
Open calculatorClassical slagging/fouling indices (B/A, Silica Ratio, Alkali Index, Fouling Index) plus a coverage-scored ternary phase liquidus estimate, computed together from one ash analysis.
Open calculatorSame classical indices and ternary phase estimate, plus a Heavy Metal Worst-Case Screen for the Zn/Pb/Ni/Cr chloride systems common in waste-derived fuels — down to 230°C for ZnCl2–KCl.
Open calculatorParticle density, dielectric constant, dipole factor and resistivity for ESP design — using a biomass-specific resistivity model, since coal-based correlations overestimate resistivity by orders of magnitude for K-rich biomass ash.
Open calculatorSame particle density and dielectric calculations, with the verified Bickelhaupt (EPRI CS-4145) resistivity correlation — well-established for coal fly ash across a wide alkali range.
Open calculatorIterative boiler tube deposit thickness over time — condensation, impaction and thermophoresis, with growing thermal resistance and a Loose→Sintered→Molten state transition tied to real eutectic melting data.
Open calculatorFull stoichiometric combustion — fuel blending, design-moisture normalization, flue gas composition, primary/secondary air split, and standard dry flow at your reference O2%.
Open calculatorNOx (fuel-N conversion, coal & biomass), SOx (alkali sulfation vs. chlorination), and dust — dry-basis ppm and mg/Nm³ at your local reference O2%.
Open calculatorCp, density, thermal conductivity, and viscosity for CO2, H2O, O2, N2, SO2 and their mixture at any composition and temperature.
Open calculatorSingle-particle trajectory through Drying, Pyrolysis, and Char Burnout on a mass-burn/travelling grate — driven by zone gas temperatures from your own process simulation.
Open calculatorHybrid furnace model — fine particles burn in suspension (ballistic trajectory + drag), coarser ones land and finish on the grate. Sweeps 8 particle sizes from 0.15–3.0 mm.
Open calculatorA simplified CO/H2 proxy for released volatile matter — tracks whether CO fully oxidizes within the furnace's plug-flow residence time, or escapes unburned.
Open calculatorDirect-method boiler duty and efficiency from steam/feedwater IAPWS-IF97 enthalpies and fuel LHV — solve for required fuel rate or check the efficiency a given rate implies.
Open calculatorConfigure your boiler's zone sequence — Furnace, Screen, Superheater, Chamber, Evaporator, Economizer, APH — and set each exit temperature from experience-based guideline ranges.
Open calculatorChecks whether Natural Circulation has enough driving force before sizing individual risers — motive head from downcomer/riser density difference, void fraction, a Darcy-Weisbach downcomer friction estimate, and drum separator loss, all balanced without double-counting.
Open calculatorRequired water-wall heating surface for the radiant furnace — Hottel-based gas radiation, convection, boiling heat transfer, fly-ash fouling, and Natural Circulation flow.
Open calculatorTube-bank cross-flow heat transfer — Zukauskas (1972) convection correlation with the digitized row-count correction table, Hottel radiation, boiling, and fouling. Works for Screen Tube before or after the Superheater.
Open calculatorSuperheated-steam tube bank — same Zukauskas/Hottel engines as Screen Tube, single-phase steam-side Dittus-Boelter, and an iterative solver that derives the real steam outlet state (temperature and pressure) from energy balance and pressure drop rather than assuming it. Also covers Reheaters.
Open calculatorAn empty, tube-lined radiant zone some biomass boilers (e.g. EFB/palm) use to shed gas temperature by radiation alone before the tube banks — same physics engine as Furnace, not present in every boiler design (bagasse boilers typically skip it).
Open calculatorA membrane-wall radiant zone with an internal heat exchanger (e.g. Superheater platens) suspended inside — same Furnace/Chamber physics, but the exchanger's own surface shortens the Mean Radiating Length calculation.
Open calculatorThe riser side of an evaporator bank tube bundle — same Zukauskas tube-bank engine as Screen Tube. Named separately from the Downcomer variant for independent linking later.
Open calculatorThe downcomer side of an evaporator bank tube bundle — same engine as the Riser variant, kept as a separately-named module so the two can be linked independently once cross-module Natural Circulation solving is built.
Open calculatorFeedwater heater — receives subcooled liquid water from the Deaerator via the high-pressure feed pump. Same Zukauskas/Hottel engines as Screen Tube, single-phase water side (IAPWS Region 1) with the same iterative outlet-state solver as Superheater. Includes live checks for economizer approach temperature and minimum feedwater inlet temperature.
Open calculatorTubular air preheater with the physics flipped from every other tube-bank module — flue gas inside the tubes (Dittus-Boelter + in-pipe radiation), combustion air outside in crossflow (Zukauskas). Proper psychrometric humidity from site dry-bulb temperature and relative humidity.
Open calculatorFlash-tank mass and enthalpy balance — two-phase flow arrives from Furnace-side and Evaporator-side riser circuits (add/remove as your boiler routes them), steam separates out, and the remaining saturated liquid mixes with Economizer feedwater to set drum water temperature. Includes a cross-check against your target steam capacity.
Open calculatorSpray attemperation between Superheater stages — high-pressure spray water from the Deaerator mixes with steam from the Primary Superheater by enthalpy balance. Includes a live check that spray pressure exceeds steam pressure by the standard 10+ bar margin needed for complete atomization.
Open calculatorSized from first-principles corona and charging physics rather than just the empirical Deutsch-Anderson constant — operating voltage is solved to the back-corona limit, efficiency uses a Matts-Ohnfeldt-form correction. Includes T-R set sizing and a discharge-electrode geometry guide from CFD field comparisons.
Open calculatorGovernor valve throttling, steam seal leak-off, and stage-by-stage expansion through any number of extraction points — back-pressure or condensing — with a Wilson-line wetness check at the wet end.
Open calculatorWhat condensing pressure your site's cooling system can actually deliver — water-cooled tower, once-through, air-cooled or hybrid — from ambient wet-bulb/dry-bulb through Approach, Range, TTD or ITD to an exhaust pressure for the Turbine module.
Open calculatorStodola's Ellipse (Cone) Law for a turbine stage group — fix any two of inlet pressure, exit pressure and flow, solve for the third, with a built-in round-trip self-consistency check.
Open calculatorMix condensate return, makeup water and heating steam to find a deaerator's steam demand and operating point — standard vs elevated pressure, with acid-dew-point guidance.
Open calculatorSize the boiler-feedwater reserve from the standard retention-time guideline (commonly 10 minutes), with an approximate vessel diameter and length.
Open calculatorWhy raising deaerator pressure never helps pump suction, and how high to elevate the tank above the boiler feed pump to deliver the NPSH it needs.
Open calculatorHow fast a spray droplet heats to saturation (Whitaker's correlation) versus how fast it sheds dissolved oxygen (diffusion in a sphere) — the mechanistic reason tray designs outperform spray-only.
Open calculatorScreen a hot surface or low-grade waste heat stream for direct electricity generation via the Seebeck effect — Ioffe maximum-efficiency equation, from ZT directly or from material properties.
Open calculatorTech Insights
Notes on the engineering behind the calculators.
A published design for 38%-moisture palm fruit bunch, from CFD to three months of continuous running.
Sign up to get notified as new modules and subscription plans launch.