PlantAISim

Engineering Notes

Behind the Calculators

Notes on the engineering that goes into PlantAISim's modules — published research and the reasoning behind the calculators. More notes will follow.

Fundamentals Electrostatic precipitators

Deutsch-Anderson vs. Matts-Ohnfeldt: Two Ways to Predict the Same ESP

Both formulas take the same three inputs — migration velocity, plate area, gas flow — and give different answers for collection efficiency. Here's why, and why it matters which one a spec sheet used.

Every electrostatic precipitator textbook opens with the same equation. Deutsch, working from Anderson's experimental data in the 1920s, proposed that collection efficiency follows from just three numbers: how fast a charged particle drifts toward the plate (migration velocity, w), how much plate area is available (A), and how much gas flows through (Q):

η = 1 − exp(−wA/Q)

It's an elegant result, and it's still the formula most engineers reach for first. It's also, measurably, too optimistic — real precipitators collect less than Deutsch-Anderson predicts, sometimes by a wide margin on the same nameplate numbers.

The assumption that breaks

Deutsch-Anderson assumes every particle behaves identically — one migration velocity, applied uniformly to a dust cloud that's actually a wide range of sizes. Real fly ash isn't one size. It's a distribution, often spanning submicron fines to tens of microns, and migration velocity depends strongly on particle size (bigger particles hold more charge but also feel more drag; the two don't cancel evenly). A single average w papers over that spread — and because the efficiency equation is exponential, averaging the wrong thing produces a real bias, not just noise.

There's a second gap Deutsch-Anderson doesn't touch: it assumes the gas moves through the precipitator as a single, well-behaved plug. Real flow has some particles re-entrained off the plates, some gas sneaking past through non-uniform velocity profiles, and dust that isn't uniformly distributed across each field's inlet. None of that is in the three-variable equation.

What Matts and Öhnfeldt changed

Working from measured performance on operating precipitators rather than the idealized derivation, Matts and Öhnfeldt (Sweden, early 1960s) proposed keeping the same three inputs but changing the exponent's shape:

η = 1 − exp(−(wA/Q)k)

with k typically fitted around 0.4–0.6 (this site's ESP module uses k=0.5, giving the square-root form 1−exp(−√(wA/Q))). Pushing the exponent below 1 does exactly what the physics calls for: it curbs the runaway optimism of the pure exponential at large wA/Q, without needing to explicitly model a particle-size distribution or a non-ideal flow field. It's a correction fitted to real plant data, not a first-principles rebuild — which is exactly why it works better in practice while staying just as simple to compute.

Why this matters when reading a spec

The two formulas can disagree by several percentage points of efficiency for the same w, A and Q — which, on a 99%-plus target, is the difference between comfortably meeting an emission limit and quietly missing it. If a vendor guarantee or an old design worksheet doesn't say which formula it used, treat the efficiency number as formula-dependent, not as a fixed physical fact. This site's own ESP module uses the Matts-Ohnfeldt form specifically because it tracks real precipitator performance more closely than the textbook-standard Deutsch-Anderson result.

Further reading

H. J. White, Industrial Electrostatic Precipitation, Addison-Wesley, 1963 — the standard English-language reference for the Deutsch-Anderson derivation and its assumptions. S. Matts and P.-O. Öhnfeldt, "Efficient gas cleaning with SF electrostatic precipitators," Flakt Report, 1963/64 — the original modified-exponent correlation.

Fundamentals Biomass combustion

Why Older Bagasse Boilers Struggle With a Fireball at the Rear Wall

Fibrous biomass fuels release most of their energy as gas, not as a glowing bed. If the furnace can't get air into that gas fast enough, the fuel burns late, burns hot in the wrong place, or doesn't finish burning at all.

Combustion engineers have a shorthand for what a flame needs to finish cleanly: the three T's — Time, Temperature, and Turbulence. A fuel-rich, high-volatile biomass like bagasse makes the third one the hard part.

Most of the fuel never touches the grate

Sugarcane bagasse is mostly volatile matter — typically 80–85% on a dry basis, with only a small fraction left as fixed carbon once the gas has driven off. In practice that means most of the fuel's heating value leaves the particle as gas within the first second or two after it enters the furnace, well before much char burnout has happened on the grate at all. The grate ends up handling a comparatively small, slower-burning fraction of the fuel; the furnace volume above and behind it has to handle the rest.

That released gas doesn't stay where it's released. In a traveling- or sloping-grate furnace, fuel is fed toward the front, so the volatile gas tends to stream up and back, concentrating where the grate meets the rear wall — the geometry, not any flaw in the fuel, pushes the bulk of the combustion toward that zone.

Why "more air" doesn't fix it on its own

Older furnace designs typically supply air in two places: under the grate (primary air, mainly there to support the bed and push some air up through it) and a modest amount of secondary air higher up. Neither is aimed at the problem. Underfire air arrives already filtered through the fuel bed and has lost most of its momentum by the time it reaches the volatile cloud above; a weak secondary air supply simply doesn't carry enough momentum to penetrate a dense, rising mass of fuel-rich gas and mix through it.

The result is a furnace that can show perfectly reasonable oxygen left over at the exit — because excess air is getting measured downstream, after it has bypassed the gas it needed to reach — while carbon monoxide at the stack stays stubbornly high. High CO together with adequate O2 is close to a diagnostic signature for exactly this: a mixing problem, not a quantity problem. Adding more total air without addressing where it goes mostly just dilutes the flue gas; it doesn't reliably reach the unburned gas sitting at the rear wall.

What a real mixing zone needs

The fix that shows up on modern biomass boiler designs, and that's largely absent from the older generation, is a dedicated overfire air system: nozzles placed to inject air directly into the volatile-rich zone, sized and aimed for enough jet momentum to actually penetrate the rising gas and fold air through it, not just add volume nearby. A few properties matter more than the absolute air quantity:

  • Velocity, not just flow. A jet needs momentum to punch into a moving gas stream. The same air volume delivered through more, smaller, higher-velocity nozzles penetrates further than the same volume through fewer, larger, slower ports.
  • Placement relative to where the gas actually is. Air aimed above or beside the real volatile plume does little; the nozzles need to target where the particle-trajectory and furnace geometry put the fuel-rich zone, which is often the rear wall for a front-fed grate, not necessarily the furnace centerline.
  • Penetration depth versus furnace width. A jet that's too weak stalls before reaching the far side of the gas stream; a jet with reach matched to the furnace cross-section mixes through the whole volatile cloud rather than just skimming its near edge.

None of this requires a large fraction of the total combustion air. Because the air only has to fix a local mixing deficit rather than add bulk oxygen, overfire air systems retrofitted onto older boilers are typically a modest single-digit percentage of total combustion air — the leverage comes from where it's delivered and how fast it's moving, not how much there is.

The trade-off worth knowing about

Staged combustion — starving the primary zone slightly and finishing the burn higher up with overfire air — is also one of the standard ways to suppress thermal NOx, since it avoids a single zone that's simultaneously hot and oxygen-rich. The same geometry that fixes a CO problem is often already doing useful work on NOx. The trade-off is that staging always has to be tuned together: push air staging too far and CO comes back from the opposite direction, now from too little oxygen too late rather than too little mixing early. Overfire air is a mixing fix layered on top of a combustion-chemistry balance, not a free variable.

Takeaways

  • High volatile fuels burn mostly in the furnace volume, not on the grate. Design the freeboard for it, not just the bed.
  • High CO with healthy exit O₂ points at mixing, not quantity. Check where the air is going before adding more of it.
  • Jet momentum, placement and penetration matter more than total overfire air volume. A well-aimed few percent beats a poorly-aimed larger share.
  • Staging affects CO and NOx together. Tune them as one system, not two separate knobs.
Fundamentals Corrosion & materials

The NOx Retrofit That Corrodes the Economizer: Ammonium Bisulfate, and How to Design Around It

Fixing NOx with ammonia injection can quietly create a worse corrosion problem downstream than the sulfuric acid dew point ever did — and it condenses at a higher, more easily-reached temperature.

SNCR and SCR both work by injecting ammonia to react with NOx. Neither reaction is perfect: some ammonia always passes through unreacted, known as ammonia slip. Downstream, that slipped NH₃ doesn't just disappear — it meets SO₃ already present in the flue gas (from sulfur in the fuel, partly oxidized further by any catalyst) and the two combine into ammonium bisulfate, NH₄HSO₄.

Why ABS is the more dangerous dew point, not the lesser one

The sulfuric acid dew point — the temperature below which SO₃ and moisture condense as liquid H₂SO₄ — is the corrosion limit most boiler designers already check for, typically somewhere in the 120–150°C range depending on SO₃ and moisture content. Ammonium bisulfate condenses at a meaningfully higher temperature, commonly cited in the roughly 150–250°C range depending on the specific NH₃ and SO₃ concentrations involved. That's the trap: a cold-end design sized purely around the sulfuric acid dew point can sit well above it — and still be squarely inside the ABS condensation window once ammonia injection is added upstream.

ABS doesn't behave like a simple acid condensate either. It forms as a sticky, viscous, mud-like deposit rather than a thin liquid film. Once that layer is there, it keeps absorbing more SO₃ and moisture from the passing flue gas, becoming progressively more acidic over time — a self-reinforcing mechanism, not a one-time condensation event. The practical result is two separate failure modes at once: fouling (the sticky deposit plugs narrow passages, especially rotary air preheater baskets, raising pressure drop and reducing heat recovery) and corrosion (the trapped acidic mud attacks the metal underneath it, often worse than exposure to H₂SO₄ condensate alone because the deposit holds the corrosive liquid against the surface rather than letting it drain or evaporate).

The design balance: stay above the dew point without giving back efficiency

The first line of defense is thermal, not metallurgical: keep the metal surface temperature of the economizer and air preheater's cold end above the ABS condensation window wherever the design can manage it. This is a genuine trade-off, not a free adjustment — the entire point of an economizer and air preheater is to pull as much heat as possible out of flue gas that's already fairly cool, and every degree of margin held above the ABS dew point is, in principle, heat left on the table that a more aggressive design could have recovered. Common ways to hold that margin without sacrificing much efficiency include raising the temperature of whatever's absorbing the heat at the cold end — for instance ensuring feedwater or combustion air entering that section isn't colder than it needs to be — so the metal wall temperature (which sits between the hot gas and the cold fluid) doesn't get pulled down into the condensation range even though the gas itself is still cooling.

Where the cold zone can't be avoided: material selection by PREN

Some geometries can't keep every surface above the dew point and still do their job — a rotary air preheater's cold-end baskets are, by definition, the coldest metal in the gas path. Where the thermal fix runs out, the next lever is the alloy itself, and the standard screening tool for that is the Pitting Resistance Equivalent Number (PREN):

PREN = %Cr + 3.3 × %Mo + 16 × %N

Chromium is what makes a stainless steel stainless in the first place — it's the baseline term and the reason plain carbon steel isn't in this conversation at all. Molybdenum is weighted nearly three and a half times as effective per percent as chromium, and is specifically what separates alloys like 316 stainless (PREN around 24) from 304 (PREN around 18) in acidic, reducing, or chloride-bearing conditions — exactly the environment a wet ABS deposit creates. Nitrogen contributes even more strongly per percent, which is part of why duplex stainless steels (PREN often above 32) resist this kind of attack better still. As a rough guide, a higher PREN alloy buys margin against localized corrosion under exactly this kind of deposit; it does not mean the metal is immune, and PREN says nothing about general corrosion rate, mechanical properties, or cost — it's a screening number for one specific failure mode, not a complete material specification.

Why a "resistant" alloy can still fail under this kind of deposit

Stainless steels resist corrosion because chromium spontaneously forms a thin, continuous, self-healing oxide film (Cr₂O₃) on the surface — the passive film. That film is what PREN is really predicting the durability of. The problem with a sticky ABS deposit specifically is that it creates exactly the local conditions that break passive films down: a stagnant, oxygen-starved, increasingly acidic pocket trapped under a porous solid, isolated from the bulk flue gas chemistry around it. This is the classic setup for under-deposit corrosion — a differential-aeration cell forms between the sheltered metal under the deposit and the exposed metal around it, and the passive film can break down locally even on an alloy that would perform perfectly well if the same acidic condensate were simply flowing freely across an open surface. It's part of why ABS fouling and ABS corrosion aren't really two separate problems to solve — the fouling (the deposit staying put) is what creates the conditions for the corrosion (the film breaking down underneath it). Controlling one goes a long way toward controlling the other.

Takeaways

  • Check the ABS dew point separately from the sulfuric acid dew point. A design margin sized only for H₂SO₄ can land inside the ABS window once ammonia injection is added.
  • Thermal margin is the first and cheapest defense. Keep cold-end metal temperature above the ABS condensation range as far as the efficiency trade-off allows before reaching for exotic alloys.
  • PREN is a screening tool, not a guarantee. Molybdenum and nitrogen buy real margin against this failure mode, but a porous deposit can still locally defeat the passive film that PREN is predicting the strength of.
  • Fouling and corrosion share a root cause here. A deposit that's hard to keep off the surface is also what creates the under-deposit conditions that attack it.
Peer-Reviewed CPESE 2021 · Energy Reports (ScienceDirect)

Designing a Step Grate for a Fuel Nobody Wants to Burn

Supphachai Srasri, Niran Bhudsarakam, Pornchai Limsutthiphong, Tanapat Ratanapitag, Amphawan Julsereewong — Design of step grate firing by utilizing palm empty-fruit-bunch fuel for industrial steam boiler construction, Energy Reports, Vol. 8, pp. 275–282 (2022), 8th International Conference on Power and Energy Systems Engineering (CPESE 2021), Fukuoka, Japan. DOI: 10.1016/j.egyr.2021.11.142

Palm empty fruit bunch (EFB) is one of the more difficult biomass fuels to burn cleanly. Fresh off the press, it carries 38.4% moisture and enough potassium in its ash to cause serious slagging and fouling inside a boiler. Most combustion equipment simply isn't designed for that combination — grate speed, air distribution, and zone geometry that work for wood pellets or bagasse tend to choke or foul on EFB.

This paper documents the design of a reciprocating step grate built specifically around EFB's combustion behavior — and the industrial boiler it was built for: 80 tons of steam per hour at 45 bar and 430°C, feedwater at 120°C, constructed and commissioned at a biomass power plant in Thailand.

Fuel Moisture
38.4%
Steam Capacity
80 t/hr
Design Pressure
45 bar
Steam Temperature
430°C

The four-zone model

The grate is split conceptually into four combustion zones the fuel bed passes through as it's conveyed by the reciprocating bars — drying, devolatilization, char combustion, and burnout — with primary air metered separately under each zone and secondary air supplied above the fuel bed for gas-phase burnout in the freeboard. CFD analysis of the bed (coupled with gas-phase radiation) gave the zone-average temperatures that shaped the final grate geometry and speed:

  • Drying zone — average 398.75°C
  • Devolatilization & combustion zones — average 730.2°C
  • Char burnout zone — average 1,063.8°C
  • Average freeboard temperature 760.96°C, dropping to 828.23°C post-radiation — high enough over the whole freeboard to confirm complete gas-phase burnout, not just localized hot spots.

From that, the grate came out at 13 m long, moving at 5 mm/s — slow enough to give EFB's high moisture content time to dry before it reaches the combustion zones, without stalling throughput.

What this has to do with PlantAISim

The bed-combustion and gas-radiation equations behind this design — Lagrangian particle drying/pyrolysis/char burnout, and the Hottel-type gas emissivity correlation used for furnace radiation — are the same physics running underneath PlantAISim's Fixed-Bed Firing and Flue Gas Thermal Properties modules. Building the step grate for a real, difficult fuel is what motivated getting that physics right in the first place; the free calculators on this site are, in a real sense, downstream of this project.

After commissioning, the grate ran continuously for roughly three months without an unplanned shutdown — the practical bar this kind of design work has to clear, CFD notwithstanding.

More notes coming

Validation write-ups, debugging deep-dives, and the reasoning behind some of PlantAISim's less obvious modeling choices — added as they're written up properly.

Suggest what to cover next