PlantAISim

Boiler Heat Transfer Train / Radiant Wall Zone

Evaporation Wall Chamber

Reference-based what this means

A membrane-wall radiant zone with an internal heat exchanger (e.g. Superheater platens) suspended inside it — same physics as Furnace/Radiation Heat Drop Chamber, but the internal exchanger's own outside surface adds into the Mean Radiating Length calculation (shortening it, since it increases the total surface competing for the same gas volume). Everything else — wall duty, U, wall heating surface, Natural Circulation — computes exactly as a normal Chamber. Leave the internal exchanger area at 0 if there isn't one.

? New here? How to use this calculator

What this answers: Same furnace-wall physics as the Furnace module, for a radiant chamber that also has a heat exchanger (like superheater platens) hanging inside it.

The numbers already in the fields are a complete, working example — not a template you must match. Overwrite any of them with your own design's values; the results update as you type.

Unfamiliar term? Look for a ? next to a field label, or browse the full Glossary.

Flue Gas (from Temperature Profile)
kg/hr
°C — from Temperature Profile
°C — from Temperature Profile
bar
Gas Composition (mol%, wet basis)
Chamber Geometry
m
m
m — chamber height, used for Volume=W×D×H
m² — real furnaces often aren't simple W×H (sloped walls); override here
m²
m² — outside area of any coil/platen physically suspended inside this chamber; adds into the Mean Radiating Length denominator only, shortening L — leave 0 if this chamber is empty
L=factor×V/A
m² — for gas velocity/Re; default=Width×Depth, override if the free-flow area differs
mm — membrane-wall tube-row surface, not smooth; adjust from experience (corrugated/riveted-metal range)
m — for the boiling correlation
Water Wall Tubes
same wall panel as Furnace — continues up
mm
mm
W/m·K
m
micron — biomass furnace typical
W/m·K
mm — commercial steel tube, typical
Steam Drum & Natural Circulation?
barg
bar — at the boiler's installation elevation

Wall temperature = saturation temperature directly (no margin added, per design experience).

Ash Particle Enhancement Factor
% of gas-side Q — typical 1.5-3%, lost to convection through insulation before reaching the tube side

From experience: ash particles enhance overall heat transfer beyond gas-only radiation models. Gas-fired boilers track the correlations closely (factor≈1.0); biomass needs the largest correction (1.5-1.6) due to fly ash particle radiation.

Duty & Natural Circulation?

Heat Transfer Coefficients?

Pressure Drop

Required Heating Surface & Tube Count?

Radiation uses the same Hottel-type correlation validated in the Flue Gas Thermal Properties module (rational-polynomial-in-log(pL), CO2/H2O/SO2, dual T-branches, Hottel & Sarofim absorptivity scaling). Gas-side convection: Dittus-Boelter through a hydraulic-diameter duct (grate/free-flow cross-section). Tube-side: Dittus-Boelter (single-phase) plus a two-phase boiling correlation, combined additively (Chen-style superposition — the specific boiling correlation form is mechanically reproduced from a real reference design but its literature source hasn't been independently identified). Overall U referenced to outside heating surface (bare-tube OD×length×count convention), with the inside (water-side) term properly scaled by the A_o/A_i area ratio. Water/steam flow required is derived from Natural Circulation theory: Circulation Ratio CR=−5.914·ln(P_drum,barg)+35.234 (biomass-specific correlation), target dryness fraction x=1/CR, Flow=Q/(h_fg×x). Gas inlet/outlet temperatures are fixed design inputs (from the Flue Gas Temperature Profile module) — this module solves directly for required area, no iteration. It does not solve multi-circuit Natural Circulation flow apportionment (this Chamber, Furnace, Screen Tube, and any other risers all sharing one drum) — the flow reported here is this section's own requirement in isolation; use the Thermal Head module to check the combined loop.

Quick reaction — was this calculator useful?

Was this calculator useful? Tell us what's missing or what you'd like to see next.

Send Feedback